The connected-cooking specialist for your Dacor.
Modernist and Contemporary ranges, gas and induction cooktops, Wi-Fi wall ovens and built-in refrigeration columns — diagnosed at the control-board and sealed-system level, recalibrated and restored to factory spec. We speak Dacor’s smart platform, not just its plumbing.
Common Dacor problems we fix.
Dacor packs more electronics into a kitchen than almost any rival, so its faults skew toward smart controls, touch panels and connectivity — alongside the ignition, calibration and cooling work any premium cooking and refrigeration brand eventually needs. These are the calls we get.
Smart controls & connectivity drop-outs
A Dacor that won’t pair, keeps losing Wi-Fi, or shows a frozen iQ / connected display is the call we take most often. We separate a software hiccup from a failed control board, antenna or power supply — and fix the root cause rather than rebooting it and hoping.
Touch panel & glass-control faults
Dead zones on a capacitive touch surface, ghost taps, a panel that lights but won’t respond, or a display gone dark. We test the membrane, ribbon connectors and control logic and fit the correct OEM panel calibrated to your model.
Gas igniters & weak spark
Clicking that never lights, a burner that lights then drops out, or an oven igniter too weak to open the gas valve. We restore reliable ignition across Dacor sealed burners, dual-stacked burners and oven bake/broil systems.
Oven temperature & calibration drift
A Dacor oven running hot, cold, or wandering off setpoint ruins precise cooking. We verify the sensor, re-establish calibration to factory spec, and confirm the cavity holds its band across a full cycle.
Convection & even-bake problems
A convection fan that rattles, won’t spin, or bakes unevenly — plus the GlideRack and four-part Pure Convection airflow Dacor is known for. We diagnose the motor, element and damper logic so heat moves the way the engineers intended.
Induction & element zones not heating
A single induction zone that won’t recognize a pan, cycles on and off, or throws an error while its neighbors work. We trace the inverter board, coil and sensing circuit instead of condemning the whole cooktop.
Refrigeration cooling & control faults
A Dacor refrigeration column drifting warm, short-cycling, frosting, or losing its set temperature. We read the sealed system, evaporator, fans and electronic controls to find why the box stopped holding its number.
Error codes & dead displays
A flashing fault code, a unit that boots into an error, or a control that won’t power up at all. We interpret the code against Dacor service data, then repair the board, sensor or supply that triggered it.
Born in California, built around bold design and smart engineering.
USA · California · California luxury with smart, connected cooking.
Dacor is a California original. The company was founded in 1965 in the Los Angeles area and spent decades as a family-run, West Coast luxury brand — close enough to the way Southern Californians actually cook and entertain that its kitchens always felt designed for the open-plan, indoor-outdoor home rather than dropped in from somewhere colder. That regional DNA still shows. Dacor leans into statement design, generous glass and color, and a willingness to put technology front and center where other luxury makers hide it.
What truly sets Dacor apart is its early, deliberate bet on connected, smart cooking. While much of the high-end market treated Wi-Fi as a gimmick, Dacor built its flagship line around it — pairing ranges and ovens to an app, layering in guided cooking, remote monitoring and software that updates over time. The result is a cooking appliance that behaves more like a connected device than a box with a thermostat. It’s genuinely useful when it works, and genuinely demanding to service correctly when it doesn’t, because the failure can live in software, in a control board, in a touch panel, or in the connectivity hardware that ties them together.
In 2016 Dacor was acquired by Samsung, and that changed the engineering trajectory in a meaningful way. Samsung’s electronics, display and connectivity expertise flowed into the platform, and Dacor’s newer Modernist appliances reflect it — richer interfaces, deeper smart features and tighter integration with the wider smart-home ecosystem. For owners it means a more capable kitchen; for a repair company it raises the bar, because servicing a current Dacor means understanding both luxury appliance fundamentals and a modern connected-device stack.
Crucially, Dacor stays in its lanes. It is a cooking and refrigeration house — ranges, cooktops, wall ovens and built-in refrigeration columns — and it builds them to disappear into the kind of custom San Diego and Orange County kitchens that are designed around the appliances rather than the other way around. That focus is exactly why a Dacor deserves a technician who knows the brand, not a generalist working off a parts diagram for the first time.
The Dacor lines we keep running.
Dacor builds cooking and refrigeration — so that’s exactly what this page covers. From the electronics-dense Modernist flagship to panel-ready cold columns, here are the families we diagnose and repair.
Modernist Collection
Dacor’s flagship — dual-fuel ranges, gas and induction cooktops and wall ovens with the connected iQ controls, push-to-open doors and the signature blue-LED cavity. The most electronics-dense line Dacor builds, and the one that rewards a tech who understands its smart platform.
Contemporary Collection
The cleaner-lined cooking range — pro-style and dual-fuel ranges, rangetops, cooktops and wall ovens that pair Dacor performance with a more restrained façade. We service its burners, ovens, convection systems and controls end to end.
Dual-fuel & gas ranges
Gas burners over an electric, convection-fed oven — the configuration serious cooks ask Dacor for. We handle ignition, valves, oven calibration, convection and the control board that ties them together.
Gas & induction cooktops
Sealed-burner gas cooktops and Dacor’s induction surfaces, including the dual-stacked burner design. We resolve no-spark, zone-recognition and inverter faults and restore precise, repeatable heat.
Wall ovens (single, double & steam-assist)
Connected wall ovens with Wi-Fi guidance, multi-mode convection and self-clean. We fix calibration drift, latch and lock faults, convection motors, door alignment and the touch controls that run them.
Built-in refrigeration columns
Panel-ready refrigerator and freezer columns built to vanish into cabinetry. We diagnose cooling loss, sealed-system and fan faults, frost issues and the electronic controls that keep each column on its number.
A smart Dacor needs a tech who reads software and sealed systems alike.
The thing that makes a modern Dacor special — its deep layer of connected electronics — is also what trips up a generalist. When a connected range misbehaves, the symptom you see in the kitchen rarely points cleanly to the cause. A frozen display might be a software fault, a failed control board, a bad ribbon connector behind the glass, or a power supply quietly browning out. A burner that won’t light could be ignition, a valve, or a control telling it not to. Swap the wrong part and the fault comes right back — usually after you’ve already paid for it.
We approach a Dacor the way it’s actually built: as an integrated system. On the cooking side that means reading the control board, touch panel and connectivity hardware together with the ignition, convection and calibration, so a smart-feature complaint and a baking complaint get traced to the same root if they share one. On the cold side it means diagnosing the sealed system, fans and electronic controls of a refrigeration column before condemning a compressor. One brand, two very different engineering disciplines — and we carry both.
Then we finish to Dacor’s standard. We fit genuine OEM Dacor control boards, touch panels, igniters, valves, sensors, convection motors and refrigeration components, and we configure them to the specific model so connected features pair correctly and the oven calibration holds. A generic substitute board may power the unit on, but it can break the smart platform or throw calibration off — which on an appliance you bought precisely for its precision is the whole thing you were paying for. We verify the repair end to end before we leave.
How a Dacor repair goes
From frozen smart panel to factory spec.
Trusted with luxury cooking and cooling.
“Our Wolf range runs like new. Respectful of the house and on time to the minute.”
“The technician explained exactly what failed on our Thermador oven and quoted before touching a thing. No surprises.”
“Liebherr wine column lost cooling on a Friday. They answered at night, came out, and saved the entire cellar.”
Dacor specialists by the numbers
Dacor repair questions, answered.
How much does a Dacor repair cost?
A flat $89 service call covers the on-site diagnosis and is credited toward your repair. Dacor repairs range widely — re-pairing a connected control or replacing an igniter is modest, while a control board or sealed-system repair costs more — so we quote the exact price only after inspecting your appliance, and always before any work begins.
Can you fix Dacor smart-control and Wi-Fi connectivity problems?
Yes — it’s the most common Dacor call we take. We diagnose whether a connectivity drop-out, frozen iQ display or unresponsive touch panel is a software fault, a failed control board, antenna or power supply, then repair the actual cause with genuine OEM parts rather than just rebooting the unit.
Do you repair both Dacor cooking appliances and refrigeration columns?
We do. Dacor builds cooking and refrigeration, and we service both — dual-fuel and gas ranges, gas and induction cooktops, and connected wall ovens on the cooking side, and panel-ready refrigerator and freezer columns on the cold side, including sealed-system and cooling-control work.
My Dacor oven is running hot or cold — can you recalibrate it?
Yes. Temperature drift usually traces to the oven sensor or lost calibration. We verify the sensor, re-establish calibration to Dacor’s factory specification, and confirm the cavity holds its setpoint across a full cycle so your baking and roasting are accurate again.
Do you use genuine Dacor parts?
Always. We fit genuine OEM Dacor control boards, touch panels, igniters, valves, sensors, convection motors and refrigeration components, configured to your exact model so connected features and calibration behave the way the factory intended.
Which areas do you cover for Dacor repair?
All of San Diego County and Orange County — including La Jolla, Rancho Santa Fe, Del Mar, Carmel Valley, Coronado, Newport Beach, Irvine and Laguna Beach. Not listed? Call us; we likely still cover your address.
Get your Dacor cooking — and cooling — exactly right again.
Factory-trained, fully insured and fluent in Dacor’s connected platform — from a frozen smart panel to a recalcitrant igniter or a column that won’t hold temperature. Reach us any time across San Diego and Orange County.
Book your Dacor repair.
Call any time — we answer 24/7 — or send your details through our quick online form. We perform jobs daily, 8AM–6PM.
Service call fee, credited toward your repair. The exact price is quoted only after a hands-on, on-site diagnosis — no surprises.
How much does it cost to repair a Dacor range or oven in San Diego?
A flat $89 service call covers the on-site diagnosis and is credited toward your Dacor repair. Cost varies by fault: re-pairing a connected iQ control or fitting an igniter is modest, while a control board or refrigeration sealed-system repair runs higher. We quote the exact price only after a hands-on diagnosis, always before any work begins.
Which Dacor product lines do you actually service?
We service Dacor's cooking and refrigeration lines: the electronics-dense Modernist Collection and cleaner-lined Contemporary Collection, dual-fuel and gas ranges, gas and induction cooktops with dual-stacked burners, single, double and steam-assist wall ovens, and panel-ready built-in refrigeration columns. Both disciplines are covered with genuine OEM Dacor parts.
Why use a Dacor specialist instead of a general repair shop?
Dacor packs more connected electronics into a kitchen than almost any rival, so a frozen iQ display might be software, a control board, a ribbon connector or a browning-out power supply, not the part a generalist swaps first. Our factory-trained techs read the smart platform and the sealed system alike, backed by a one-year written workmanship guarantee.
Local dispatch
Based near San Diego. Routed across SD & OC.
A central San Diego map pin for same-week luxury appliance repair routes across San Diego County and Orange County.